Select your language

Capacity control in cooling systems (I)

Saving energy is one of the most sought-after concepts in recent times within our industry, and the principle of capacity control is one of them.

by Alonso Amor*

The continuous search for more efficient solutions has led the refrigeration industry to the implementation of systems focused on having a high impact energy saving, offering sustainability to both stored products and equipment.

There are several strategies aimed at saving energy in the industry, being that many of them have as a principle the control of capacity.

- Publicidad -

Every cooling system is calculated on the same principle: there is a fixed thermal load (to a design condition) under which the equipment is sized and based on the selection it must be controlled. There are several factors that cause the load to be variable, such as: the ambient temperature, the temperature of the product throughout the day (or process) and even the thermal load resulting from the operation of the premises itself (opening and closing doors). All these factors bring as a necessity a control of the capacity of the system.

There are different types of capacity control, the most common are those that base their operation on turning the system on and off, however, this measure does not bring any benefit in energy savings to the installation. This text seeks to publicize the benefits of those solutions where, in addition to having a variable capacity, there are benefits in energy savings and sustainability of the system. The solutions that will be addressed are the following:

  • Variable capacity compressors
  • Electronic expansion valves
  • Floating suction
  • Evaporator/condenser fan speed control

The principle of energy saving in refrigeration installations can be seen from different angles, however, the objective is always common: to use the minimum capacity necessary in the most efficient way to guarantee the desired conditions in the stored product.

Variable Capacity Compressors

In order to control the capacity of a cooling system, without a doubt, one of the main points is the control of the compression stage. There are several ways to do this, the most common of which is to divide the total load into different compressors to have different stages of capacity according to the current load required. This is the technique most commonly used by supermarket refrigeration systems, where these sets of parallel compressors are better known as racks.

Compressor racks have been the most used solution in cooling systems with capacity control, however, due to their robust control (capacity control is a function of the number of compressors) they do not represent an optimized solution that in addition to seeking demand control contributes to the need for better temperature control and system adjustment.

An improvement to this type of system is the incorporation of capacity control by means of dischargers incorporated into the compressors individually. With this it is possible to have a greater number of control stages and thus obtain a more stable condition of suction pressure and temperature. Dischargers are usually applied to reciprocating compressors by means of blocked suction, that is, the gas is prevented from entering the compression chamber, leaving the pistons in motion without refrigerant flow. This technique is applied by heads, for example for a three-head compressor (six pistons) you will have 100%, 67%, 33% and 0% capacity respectively.


- Publicidad -

The methods mentioned above are effective and help to have a control of the installation, however, the current requirements of the facilities have led the refrigeration systems to use even more precise methods with more exact capacity variations and notable benefits in electricity consumption.

Faced with this need, two types of technologies have been applied: capacity control by frequency inverter (variator) and capacity control by digital technology.

Control by frequency inverter

It consists of the variation of the electrical frequency of supply of the compressor, with this a modulation in the speed of rotation of the motor is achieved, thus controlling the capacity of the compressor. From an energy point of view, this method has great benefits due to the fact that while the capacity is modulated in a linear way, the energy consumption falls into a cubic relationship (see graph 1).

In this way as long as 100% of the compressor is not necessary, not only can you have an excellent modulation but also a positive effect in terms of energy savings. In addition, there is as such no electrical limitation for frequency modulation within the operating ranges of the network, so the capacity stages can be as fine as the accuracy of the inverter used.

- Publicidad -

Figure 1: Capacity/Consumption Curve Compressor with Frequency Inverter

For example, if the compressor is working at 80% of its rotation (40 Hz) its cooling capacity will also be 80% and its electricity consumption will only be 51%.

Capacity control by frequency inverter is a fairly effective method, however, the limits established by the compressor manufacturer must be considered, as there are restrictions mainly linked to working in low rotations since it can lead to lubrication deficiencies. The natural frequency of the compressor must also be taken into account, because when crossing by this value the system can enter into resonance generating strong vibrations and even rupture of pipe or components. Commonly compressors with frequency inverter work in a range between 25 and 60 Hz depending on the application.

Control by digital technology

It consists of intermittent compression in a fixed interval, where the percentage of capacity will be given by the percentage of that interval in which the compressor (or part of it is compressing). For example, in an interval of 20 seconds a compressor will be at 50% if it compresses 10 seconds and the remaining 10 seconds works in a discharged manner (see graph 2).

Graph 2: Modulation of Digital Compressor in Interval of 20 Seconds

In this method of capacity control the engine always works at a constant rotation, the energy consumption varies according to the presence or absence of refrigerant gas inside the compression chamber, it is calculated that when the compressor is discharged it consumes 10% of energy compared to its work in compression regime.

In Scroll compressors, modulation occurs over 100% capacity of the compressor, this is achieved by separating the spirals. Already in reciprocating compressors this technology is applied only to one head (by blocked suction) leaving the possibility of having additional capacity control in the remaining pistons.

Note: in the following article we will continue with the development of these recommendations for the capacity control of cooling systems, delving into topics such as electronic expansion valves, floating suction and fan speed control.

* Eng. Alonso Amor. Technical Manager Flow Controls Latin America. Emerson Climate Technologies. Guadalajara, Jalisco, Mexico. [email protected]

No comments

• If you're already registered, please log in first. Your email will not be published.

Leave your comment

In reply to Some User
Building Automation Days 2025 in Bogota marks a milestone for the KNX standard in Latin America

Building Automation Days 2025 in Bogota marks a milestone for the KNX standard in Latin America

Colombia. With more than a hundred attendees and the participation of six high-profile exhibitors, Building Automation Days by KNX LATAM, Colombia edition, established itself as the most relevant...

Design Envelope Technology Hits 750 gpm Fire Pump Segment

Design Envelope Technology Hits 750 gpm Fire Pump Segment

Canada. In response to the growing demands of the fire protection industry, Armstrong Fluid Technology announced the expansion of its Vertical-In-Line pump line with the addition of the new 5x4x10PF...

Greenheck Launches New RV-220 Model and Expands Its Line of Dedicated Outdoor Air Systems

Greenheck Launches New RV-220 Model and Expands Its Line of Dedicated Outdoor Air Systems

United States. Greenheck announced the addition of the RV-220 to its line of dedicated outdoor air systems (DOAS), a solution that responds to the growing demand for equipment with greater outdoor...

Embraco enters the HVAC market with new scroll compressors and aims to become a full-service supplier

Embraco enters the HVAC market with new scroll compressors and aims to become a full-service supplier

Brazil. Embraco announced its official entry into the heating, ventilation and air conditioning (HVAC) market following the acquisition of the specialized company Xecom, and the launch of a new line...

SIGMAN GROUP and Carrier-VRF reinforce technical training in the HVAC sector in Ecuador

SIGMAN GROUP and Carrier-VRF reinforce technical training in the HVAC sector in Ecuador

Ecuador. An intensive week of technical and commercial training brought together key players in the HVAC sector in Quito and Guayaquil, thanks to the joint initiative of GRUPO SIGMAN and...

AHR Expo Mexico 2025 returns to Monterrey with its most ambitious edition yet

AHR Expo Mexico 2025 returns to Monterrey with its most ambitious edition yet

Mexico. The event returns this year to Monterrey with an unprecedented edition. The exhibition, dedicated to air conditioning, ventilation, heating, refrigeration and filtration solutions, promises...

Fujitsu Launches New AIRSTAGE Multi-Position Air Handler with R-32 Refrigerant

Fujitsu Launches New AIRSTAGE Multi-Position Air Handler with R-32 Refrigerant

United States. Fujitsu General America announced the launch of its new AIRSTAGE Multi-Position Air Handling Unit (MPAHU), designed to provide greater application flexibility by easily...

HVAC project at the Javeriana University, finalist in the CALA Awards 2025 in the HVAC category

HVAC project at the Javeriana University, finalist in the CALA Awards 2025 in the HVAC category

The HVAC system installed in the building of the Faculty of Sciences of the Pontificia Universidad Javeriana, in Bogotá, was selected as a finalist in the HVAC category of the CALA Awards 2025. The...

Concord Project in La Lima Free Trade Zone, finalist in the HVAC category of the CALA Awards 2025

Concord Project in La Lima Free Trade Zone, finalist in the HVAC category of the CALA Awards 2025

The HVAC system project carried out by MultiFRIO for the company Concord in the La Lima Free Trade Zone, in Cartago, received the final prize in the HVAC category of the CALA Awards 2025, a...

HVAC project at the Universidad Santiago de Cali, finalist in the CALA AWARDS HVAC category

HVAC project at the Universidad Santiago de Cali, finalist in the CALA AWARDS HVAC category

The air conditioning project of the Auditorium Building and the Technology Center of the new campus of the Santiago de Cali University was chosen as a finalist in the HVAC category of the CALA...

Free Subscription
Remember Me
SUBSCRIBE TO OUR NEWSLETTER
DO YOU NEED A SERVICE OR PRODUCT QUOTE?
LASTEST INTERVIEWS
SITE SPONSORS










LASTEST NEWSLETTER
Ultimo Info-Boletin